image

Electro Permanent Magnetic Chuck (EPM)

Quad-Pole Magnetic Workholding

Electro Permanent Magnetic Chuck (EPM)

Application

The Electro Permanent Magnetic Chuck is designed for VMC and CNC machines, especially for milling operations.

It overcomes the drawbacks of conventional workholding by eliminating mechanical clamping, enabling quick workpiece release and allowing five-face machining for improved productivity.

Characteristics

External power is required only to energize or de-energize the chuck. No electrical power is required during machining, while the rigid magnetic force supports the required depth of cut with accuracy.

Characteristics

  • Designed for VMC and CNC machines, especially for milling operations.
  • Requires external power only for energizing and de-energizing the chuck.
  • Continuous electrical power is not required during the machining operation.
  • Provides rigid magnetic force corresponding to the required depth of cut.
  • Designed to avoid mechanical clamping and allow easy and quick release of the workpiece.
  • Five-face machining is possible, saving setup time and increasing productivity.
  • Pole gap, pole pitch, pole width and pole style can be defined to suit the workpiece.

Construction & Operation

  • Fabricated using high-permeability steel for the overall body.
  • Quad-pole magnetic face provides the required magnetic workholding arrangement.
  • Pole separation is provided using epoxy resin.
  • Copper wire is used as the conductor with Class-H insulation.
  • FRP former is used as the winding base and epoxy potting is provided.
  • The chuck incorporates two different characteristics of permanent magnets.
  • Operation is controlled through an operating pendant for energizing and de-energizing.

Inspection & Accessories

Each chuck can be inspected through electrical and magnetic tests to verify its operating condition and performance. Accessories are available for operating the chuck above the machine setup.

Earth Terminal Test Demagnetizing Test Pulling Force Test Operating Pendant Thyristor Control Capacitor Discharge Unit
EPM Milling Workholding

Rigid holding without continuous power

The chuck uses two types of permanent magnets and needs an external supply only while switching ON or OFF. Once energized, it maintains magnetic holding force without continuous electrical power during machining.

Power is required only for switching. Confirm that the workpiece is correctly positioned and the chuck is fully energized before beginning the machining operation.

Operating Guidelines

  1. Use the Electro Permanent Magnetic Chuck for its intended VMC and CNC milling applications.
  2. Ensure the workpiece is correctly positioned on the magnetic chuck surface before starting machining.
  3. Verify that the chuck is properly energized before commencing the machining operation.
  4. Use the operating pendant correctly for energizing and de-energizing the chuck.
  5. Ensure the electrical connections and earth terminal are in proper condition before operation.
  6. Check the demagnetizing function and magnetic holding performance as part of the recommended inspection procedure.
  7. Do not exceed the chuck's intended operating conditions or use it outside its specified machining application.

Operation Sequence (Follow the steps)

01

Connect the chuck to the Thyristor Control Impulse Unit or Capacitor Discharge Unit and operating pendant.

02

Clean the magnetic face and the workpiece contact surface.

03

Position the workpiece correctly across the quad-pole magnetic face.

04

Use the operating pendant to energize the chuck.

05

Confirm rigid magnetic holding before starting the milling operation.

06

Machine the exposed faces; five-face machining can reduce repeated setups.

07

Stop the machine and use the pendant to de-energize and demagnetize the chuck.

08

Remove the released workpiece and prepare the chuck for the next job.

Available Sizes

Available models are listed with their nominal Length × Width × Height dimensions and pole gap.

Model Code Size (L × W × H) Pole Gap
003-01-01 450 × 230 × 80 mm 15 mm
003-01-02 610 × 450 × 80 mm 15 mm
003-01-03 780 × 375 × 90 mm 15 mm
Applications

Precision Machining & Workholding

Electro permanent magnetic chuck control unit and operating pendant
Control Unit & Operating Pendant
Electro permanent magnetic chuck used on a VMC milling machine
VMC Milling Operation
Electro permanent magnetic chuck used for CNC milling workholding
CNC Milling Workholding
Need help choosing a model?

Share your workpiece and machining details with our team.

WhatsApp
Call Us