image

Electromagnetic Lifter - Rectangle Shape

Material Handling Magnets

Electromagnetic Lifter - Rectangle Shape

Application

Electromagnetic Lifter is a device required for easy handling of material, so that laborious and time-consuming work can be avoided.

For materials that have no provision for engaging a crane hook or similar arrangement, a magnetic lifter provides an effective solution. It therefore increases efficiency and productivity.

Safety Factors

We provide a three-times factor of safety. If a lifter is recommended for a 100 kg lifting capacity, it is tested for 300 kg. In practice, unevenness, scaling, coatings, punched characters or numbers may create a gap between the magnetic face and the lifting object, so this safety factor is essential.

Characteristics

  1. This device requires a continuous D.C. power supply while energized (ON). A fail-safe battery backup facility is available at extra cost.
  2. A lifter recommended for 100 kg is tested for 300 kg, providing a three-times safety factor.
  3. The 1:3 recommended-load-to-test-load safety factor supports optimal working conditions even with substantial operating air gaps.
  4. When using multiple lifters, an M.S. fabricated tackle is required to balance the plate and avoid sagging. The tackle is designed according to plate size.

Operating Instructions

  1. Electromagnetic Lifter is used for any ferrous material.
  2. The magnetic field is controlled using the operating pendant: Magnet ON and Magnet OFF.

Scope of Supply

A) Electromagnetic Lifter.
B) Control Panel (Rectifier unit).
C) Operating Pendant.

Accessories

A) M.S. Fabricated Tackle
B) Slings, Chains, 'D' shackles and links
C) Flexible Cable
D) Cable Carriers
E) Cable Drum
F) Wire Rope for Cable Carriers
G) Clamps for Wire Rope
H) Control panel unit consisting of electrical spares

Performance of Lifter

Consider 40% lifting force when lifting a round job because of its line contact. For 100% use of the recommended capacity, close contact is required between the magnetic face and lifting object.

Safety Related NORMS

Lifters are load-tested on a Universal Testing Machine (UTM), certified by the laboratory and supplied with the certificate. With the three-times factor of safety, a lifter recommended for 100 kg must lift at least 300 kg during testing.

NOTE: Load testing is recommended at least once a year to confirm lifting capacity and the service life of spares.

Precautions

  1. Use the lifter only for the application for which it is made.
  2. Do not lift beyond the recommended lifting capacity.
  3. Ensure adequate contact area and balance while lifting.
  4. Do not attempt to lift very hot jobs.
  5. Keep magnetic faces clean and free from dents.
  6. When unused for a long period, apply grease or oil to magnetic faces to prevent rust.
  7. Test the load at least once a year. Also inspect the control panel, fabricated tackle, chains, slings and other spares to confirm lifting capacity and service life.

Operation Sequence (Follow the steps)

01

Install the control panel on the crane or at a nearby location.

02

Provide an external A.C. supply to the control panel.

03

Connect the control panel to the Electromagnetic Lifter and operating pendant.

04

Hang the lifter with an M.S. fabricated tackle.

05

Hang the complete assembly from the crane hook.

06

Align the lifter properly on the lifting object and verify its position.

07

Press Magnet ON on the operating pendant to energize the lifter.

08

Lift approximately 6 inches and confirm that the load is held correctly.

09

Move it to the required place at a minimum height, approximately one foot above ground.

10

Set the load down properly, then press Magnet OFF to de-energize the lifter.

Available Sizes

Nominal dimensions are shown as Length × Width × Height. Self-weights are approximate.

Code No. Nominal Size (L×W×H) Lifting Capacity Self Weight (Approx.)
011-02-01 250 × 120 × 100 mm 250 kg 17 kg
011-02-02 350 × 120 × 120 mm 500 kg 25 kg
011-02-03 400 × 150 × 80 mm 1000 kg 35 kg

Applications

Checkered plate handling with rectangle electromagnetic lifters
Checkered Plate Handling
Heavy plate handling with rectangle electromagnetic lifters
Heavy Plate Handling
Multi-lifter heavy plate handling arrangement
Heavy Plate Handling
Junction box and pendant for electromagnetic lifter
Junction Box

Large or long plates may require a purpose-designed multi-lifter tackle to balance the load and prevent sagging.

Need help choosing a model?

Share your load details with our team.

WhatsApp
Call Us