image

Electromagnetic Lifter For Scrap Lifting Circular Shape

Material Handling Magnets

Electromagnetic Lifter For Scrap Lifting Circular Shape

Application

This special type of Electromagnetic Lifter is especially used for scrap lifting and requires a continuous D.C. power supply while energized (ON).

The effectiveness of its lifting capacity varies according to the contact area of the scrap. Uneven scrap contact can considerably reduce the practical lifting capacity compared with a solid load.

Performance of Lifter

A lifter rated for 10 tons can lift a 10-ton solid load with 100% close contact. With uneven scrap contact, it may lift approximately 5–10% of its rated capacity, or about 500 to 1,000 kg.

Construction of Electromagnetic Lifter

  • Overall body fabricated from high-permeability steel.
  • Conductor made from enamelled copper wire.
  • Class-H insulation with an FRP winding former.
  • Input: 415 V, three-phase, 50 Hz A.C. supply.
  • Output operating voltage: 220 V D.C.
  • Operation through an operating pendant.

Characteristics of Control Panel

  • Input: 415 V, three-phase, 50 Hz A.C. supply.
  • Output operating voltage: 220 V D.C.
  • Three-phase bridge rectifier using silicon diodes.
  • A.C. and D.C. supply protected using fuses.
  • Three red, yellow and blue (RYB) indicator bulbs.

Scope of Supply & Accessories

Scope of supply:
A) Electromagnetic Lifter
B) Control Panel (Rectifier unit)
C) Operating Pendant

Control Panel Operating Pendant Cable Drum Flexible Cables Cable Carriers Wire Rope Clamps Control-panel Electrical Parts

Performance of Lifter

Lifting effectiveness varies according to contact between the magnetic face and lifting object. A 10-ton lifter with 100% close contact can lift a 10-ton solid load, but scrap has uneven contact and therefore may achieve only a fraction of the total rated capacity.

Scrap Lifting Capacity

Scrap may provide only approximately 5–10% of the lifter's rated capacity. For example, a 10-ton model may lift approximately 500 to 1,000 kg of scrap. Actual capacity varies with uneven contact area.

Operating Instructions

  1. Ensure the required control panel is installed on the crane or at a suitable nearby location.
  2. Provide the specified external A.C. power supply to the control panel before operating the lifter.
  3. Connect the control panel with the electromagnetic lifter and operating pendant correctly.
  4. Hang the lifter assembly securely from the crane hook using the provided three-legged chain arrangement.
  5. Align the magnetic face properly with the scrap before energizing the lifter.
  6. Operate the Magnet "ON" button on the operating pendant to energize the electromagnetic lifter.
  7. Lift the scrap only to the required and safe height and carry the load with minimum practical clearance.
  8. After reaching the desired location, place the load securely before switching the Magnet "OFF".
  9. Ensure the magnet is completely de-energized after unloading and before moving the lifter away from the load.

Operation Sequence (Follow the steps)

01

Install the control panel on the crane or at a nearby location.

02

Provide the external A.C. supply to the control panel.

03

Connect the control panel to the lifter and operating pendant.

04

Hang the complete lifter assembly from the crane hook.

05

Align the lifter properly on the material to be lifted.

06

Press Magnet ON on the operating pendant to energize the lifter.

07

Lift the scrap to the recommended height.

08

Carry the scrap to the desired place while maintaining minimum height.

09

At the desired place, press Magnet OFF to de-energize the lifter and release the scrap.

Available Sizes

Circular electromagnetic scrap lifters are available in different diameters and lifting capacities. The lifting capacities shown are based on 100% close contact with the lifting material. Actual scrap lifting capacity may vary depending on the contact area and condition of the scrap.

Model Code Nominal Size (Dia. × H) Lifting Capacity
(100% Close Contact)
Self Weight (Approx.)
011-03-01 Dia. 700 × H250 mm 7,000 kg 800 kg
011-03-02 Dia. 1000 × H250 mm 10,000 kg 1,600 kg
011-03-03 Dia. 1400 × H250 mm 15,000 kg 3,000 kg
011-03-04 Dia. 1600 × H250 mm 17,000 kg 4,000 kg
011-03-05 Dia. 1900 × H250 mm 20,000 kg 6,000 kg

Note: Lifting capacities are specified for 100% close contact. Due to uneven contact areas in scrap lifting applications, actual lifting capacity may vary depending on the type, size and contact condition of the scrap.

Applications

Metal parts lifting with circular electromagnetic scrap lifter
Metal Parts Lifting
Trimming metal wire bundle lifting
Trimming Metal Wire Bundle Lifting
Trimming metal wire bundle held by an electromagnetic lifter
Trimming Metal Wire Bundle Lifting
Control panel with operating pendant
Control Panel with Operating Pendant
Operating pendants for magnet and crane
Pendant for Magnet & Crane

Scrap lifting capacity varies according to the uneven contact area between the magnetic face and the material.

Need help choosing a model?

Share your load details with our team.

WhatsApp
Call Us