image

Electromagnetic Chuck – Heavy Duty Multi Coil

Magnetic Chucks for Grinding & Milling Operations

Electromagnetic Chuck (Heavy Duty Multi Coil Fine Pitch Transverse Poles)

Application

This electromagnetic chuck is designed for grinding operations and generates strong magnetic force to hold the workpiece rigidly.

It operates on continuous D.C. power. With no internal wear or deformation caused by moving internal parts, it provides a longer life than a conventional permanent magnetic chuck.

Fine-Pitch Configuration & Accuracy

The heavy-duty multi-coil transverse-pole face has a 1 mm pole gap and 2 mm pole pitch. Accuracy is maintained as per IS 8710-1978.

Construction of Electromagnetic Chuck

  • Fabricated overall body made from high-permeability steel.
  • Pole separation using brass strips.
  • Enamelled copper-wire conductor.
  • Class-H insulation with an FRP winding former.
  • Epoxy-potting bonding and continuous D.C. operation.
  • Operation through an operating pendant.

Characteristics of Control Panel

  • Input power supply: 230 V A.C.
  • Output operating voltage: 110 V D.C.
  • A.C. and D.C. supplies protected by fuses and MCB.
  • Indicators for main supply, Magnet ON and demagnetizing cycle.

Inspection & Accessories

Inspection tests:
1) Resistance-to-earth terminal test
2) Demagnetizing test
3) High-voltage test
4) Leak-proof test
5) Slipping-force test as per IS 8710-1978

D.C. Power Supply UnitMag/Demag UnitOperating Pendant

Tested for dependable workholding

The Heavy Duty Multi Coil Electromagnetic Chuck is designed for reliable and rigid workholding during grinding operations. The chuck and its control system are inspected through electrical and magnetic performance tests to help ensure safe and dependable operation.

Control Requirement

A D.C. power-supply unit or Mag/Demag unit is required to operate the electromagnetic chuck.

Essential Precautions

  1. Use the electromagnetic chuck only for its intended grinding and machining applications.
  2. Ensure the workpiece is properly positioned and has adequate contact with the magnetic pole surface before starting the operation.
  3. Operate the chuck with the specified DC power supply and approved control panel.
  4. Check the electrical connections, cables and control-panel components before operation.
  5. Keep the chuck surface clean and free from chips, dirt and other material that may affect proper workpiece contact.
  6. Do not operate the equipment if there is any abnormal electrical condition, damaged wiring or control-panel fault.
  7. Periodically inspect the chuck through appropriate electrical and magnetic tests, including earth-terminal, demagnetizing, high-voltage, leakage and holding-force checks.

Operation Sequence (Follow the steps)

01

Connect the chuck to the D.C. power-supply or Mag/Demag control unit.

02

Clean the chuck surface and ferrous workpiece contact face.

03

Position the workpiece correctly on the fine-pitch transverse-pole surface.

04

Switch Magnet ON using the operating pendant.

05

Confirm rigid magnetic holding before starting the grinding operation.

06

Perform grinding while maintaining continuous D.C. supply.

07

Stop the machine and initiate the demagnetizing cycle after grinding.

08

Remove the workpiece only after demagnetization is complete.

Available Sizes

Heavy Duty Multi Coil Electromagnetic Chucks are available in various standard sizes with a 1 mm pole gap and 2 mm pole pitch.

Model Code Size (L × W × H) Pole Gap Pole Pitch
002-03-01 450 × 150 × 100 mm 1 mm 2 mm
002-03-02 500 × 200 × 100 mm 1 mm 2 mm
002-03-03 600 × 200 × 100 mm 1 mm 2 mm
002-03-04 600 × 250 × 100 mm 1 mm 2 mm
002-03-05 750 × 250 × 100 mm 1 mm 2 mm
002-03-06 900 × 250 × 100 mm 1 mm 2 mm
002-03-07 600 × 300 × 100 mm 1 mm 2 mm
002-03-08 750 × 300 × 100 mm 1 mm 2 mm
002-03-09 900 × 300 × 110 mm 1 mm 2 mm
002-03-10 1000 × 250 × 110 mm 1 mm 2 mm
002-03-11 1000 × 300 × 110 mm 1 mm 2 mm
002-03-12 1500 × 250 × 110 mm 1 mm 2 mm
002-03-13 1500 × 300 × 110 mm 1 mm 2 mm
002-03-14 1500 × 400 × 110 mm 1 mm 2 mm

Applications

Mag Demag unit with pendant for fine-pitch electromagnetic chuck
Mag/Demag Unit with Pendant

A D.C. power-supply unit or Mag/Demag unit is required for operating the electromagnetic chuck.

Need help choosing a model?

Share your load details with our team.

WhatsApp
Call Us